NX1P2 NX-series NX1P2 CPU Units/Lineup | Omron Bangladesh by Kyoto engineering & Automation

The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, CE: EU Directives, RCM: Regulatory Compliance Mark and KC: KC Registration.
Contact your OMRON representative for further details and applicable conditions for these standards.

Product Name	Pro- gram ca- paci- ty	Memory capacity for variables	Maximum number of used real axes			Total number of built-in I/O points			Model	Stand- ards
Product Name	Pro- gram ca- paci- ty	Memory capacity for variables		Used motion control servo axes	Used single- axis position control servo axes		Number of input points	Number of output points	Model	Stand- ards
NX1P2 CPU Unit	1.5 MB	32 KB (Retained during power inter- ruptions) or 2 MB (Not retained during power inter- ruptions)	8 axes	4 axes	4 axes	40 points	24 points	16 points, NPN transistor	NX1P2-1140DT	UC1, CE, RCM, KC
			8 axes	4 axes	4 axes			16 points, PNP transistor *	NX1P2-1140DT1
			6 axes	2 axes	4 axes			16 points, NPN transistor	NX1P2-1040DT
			6 axes	2 axes	4 axes			16 points, PNP transistor *	NX1P2-1040DT1
			4 axes	0 axes	4 axes	24 points	14 points	10 points, NPN transistor	NX1P2-9024DT
			4 axes	0 axes	4 axes	24 points	14 points	10 points, PNP transistor *	NX1P2-9024DT1

Note: One NX-END02 End Cover is provided with the NX1P2 CPU Unit.
* With the load short-circuit protection.

The Option Boards are mounted to the option board slot on the CPU Unit.

Product Name	Specification	Supported protocol	Model	Stand- ards
Serial Communications Option Board	One RS-232C port. Transmission distance: 15 m. Connection type: Screwless clamping terminal block (9 terminals).	Host link, Modbus-RTU master, and no-protocol	NX1W-CIF01	UC1, CE, RCM, KC
	One RS-422A/485 port. Transmission distance: 50 m. Connection type: Screwless clamping terminal block (5 terminals)		NX1W-CIF11
	One RS-422A/485 port (isolated). Transmission distance: 500 m. Connection type: Screwless clamping terminal block (5 terminals)		NX1W-CIF12
Analog I/O Option Board	Analog input: 2 Voltage input: 0 to 10 V (Resolution: 1/4,000). Current input: 0 to 20 mA (1/2,000) Connection type: Screwless clamping terminal block (5 terminals)		NX1W-ADB21
	Analog output: 2 Voltage output: 0 to 10 V (Resolution: 1/4,000) Connection type: Screwless clamping terminal block (3 terminals)		NX1W-DAB21V
	Analog input: 2/Analog output: 2 Voltage input: 0 to 10 V (Resolution: 1/4,000). Current input: 0 to 20 mA (1/2,000) Voltage output: 0 to 10 V (Resolution: 1/4,000) Screwless clamping terminal block (8 terminals)		NX1W-MAB221

Up to eight NX Units can be connected to an NX1P2 CPU Unit.

Product Name	Specification					Model	Standards
Product Name	Number of points	Internal I/O common	Rated input voltage	I/O refreshing method	ON/OFF response time	Model	Standards
DC Input Unit (Screwless Clamping Terminal Block, 12 mm Width)	4 points	NPN	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID3317	UC1, N, L, CE, RCM, KC
			24 VDC		100 ns max./ 100 ns max.	NX-ID3343
			24 VDC	Input refreshing with input changed time only *	100 ns max./ 100 ns max.	NX-ID3344
		PNP	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID3417
			24 VDC		100 ns max./ 100 ns max.	NX-ID3443
				Input refreshing with input changed time only *	100 ns max./ 100 ns max.	NX-ID3444
	8 points	NPN		Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID4342
	8 points	PNP				NX-ID4442
	16 points	NPN				NX-ID5342
	16 points	PNP				NX-ID5442
DC Input Unit (M3 Screw Terminal Block, 30 mm Width)	16 points	For both NPN/PNP	24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID5142-1	UC1, CE, RCM, KC
DC Input Unit (MIL Connector, 30 mm Width)	16 points	For both NPN/PNP	24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID5142-5	UC1, CE, RCM, KC
DC Input Unit (MIL Connector, 30 mm Width)	32 points	For both NPN/PNP	24 VDC		20 μs max./ 400 μs max.	NX-ID6142-5	UC1, CE, RCM, KC
DC Input Unit (Fujitsu Connector, 30 mm Width)	32 points	For both NPN/PNP	24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	20 μs max./ 400 μs max.	NX-ID6142-6	UC1, CE, RCM, KC
AC Input Unit (Screwless Clamping Terminal Block, 12 mm Width)	4 points	200 to 240 VAC, 50/60 Hz (170 to 264 VAC, ±3 Hz)		Free-Run refreshing	10 ms max./ 40 ms max.	NX-IA3117	UC1, N, CE, RCM, KC

* To use input refreshing with input changed time, the EtherCAT Coupler Unit with unit version 1.1 or later and the
Sysmac Studio version 1.07 or higher are required.

Product Name	Specification						Model	Stand- ards
Product Name	Number of points	Internal I/O common	Maximum value of load current	Rated voltage	I/O refreshing method	ON/OFF response time	Model	Stand- ards
Transistor Output Unit (Screwless Clamping Terminal Block, 12 mm Width)	2 points	NPN	0.5 A/point, 1 A/Unit	24 VDC	Output refreshing with specified time stamp only *	300 ns max./ 300 ns max.	NX-OD2154	UC1, N, L, CE, RCM, KC
	2 points	PNP	0.5 A/point, 1 A/Unit	24 VDC	Output refreshing with specified time stamp only *	300 ns max./ 300 ns max.	NX-OD2258
	4 points	NPN	0.5 A/point, 2 A/Unit	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	0.1 ms max./ 0.8 ms max.	NX-OD3121
		NPN		24 VDC		300 ns max./ 300 ns max.	NX-OD3153
		PNP				0.5 ms max./ 1.0 ms max.	NX-OD3256
						300 ns max./ 300 ns max.	NX-OD3257
			2 A/point, 8 A/Unit			0.5 ms max./ 1.0 ms max.	NX-OD3268	UC1, CE, RCM, KC
	8 points	NPN	0.5 A/point, 4 A/Unit	12 to 24 VDC		0.1 ms max./ 0.8 ms max.	NX-OD4121	UC1, N, L, CE, RCM, KC
	8 points	PNP		24 VDC		0.5 ms max./ 1.0 ms max.	NX-OD4256
	16 points	NPN		12 to 24 VDC		0.1 ms max./ 0.8 ms max.	NX-OD5121
	16 points	PNP		24 VDC		0.5 ms max./ 1.0 ms max.	NX-OD5256
Transistor Output Unit (M3 Screw Terminal Block, 30 mm Width)	16 points	NPN	0.5 A/point, 5 A/Unit	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	0.1 ms max./ 0.8 ms max.	NX-OD5121-1	UC1, CE, RCM, KC
	16 points	PNP	0.5 A/point, 5 A/Unit	24 VDC		0.5 ms max./ 1.0 ms max.	NX-OD5256-1	UC1, CE, RCM, KC
Transistor Output Unit (MIL Con- nector, 30 mm Width)	16 points	NPN	0.5 A/point, 2 A/Unit	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	0.1 ms max./ 0.8 ms max.	NX-OD5121-5	UC1, CE, RCM, KC
	16 points	PNP	0.5 A/point, 2 A/Unit	24 VDC		0.5 ms max./ 1.0 ms max.	NX-OD5256-5
	32 points	NPN	0.5 A/point, 2 A/ common, 4 A/Unit	12 to 24 VDC		0.1 ms max./ 0.8 ms max.	NX-OD6121-5
	32 points	PNP	0.5 A/point, 2 A/ common, 4 A/Unit	24 VDC		0.5 ms max./ 1.0 ms max.	NX-OD6256-5
Transistor Output Unit (Fujitsu Connector, 30 mm Width)	32 points	NPN	0.5 A/point, 2 A/ common, 4 A/Unit	12 to 24 VDC	Switching Synchronous I/O refreshing and Free- Run refreshing	0.1 ms max./ 0.8 ms max.	NX-OD6121-6	UC1, CE, RCM, KC

Product Name	Specification					Model	Standards
Product Name	Number of points	Relay type	Maximum switching capacity	I/O refreshing method	ON/OFF response time	Model	Standards
Relay Output Unit (Screwless Clamping Terminal Block, 12 mm Width/ 24 mm Width)	2 points	N.O.	250 VAC/2 A (cosφ=1) 250 VAC/2 A (cosφ=0.4) 24 VDC/2 A 4 A/Unit	Free-Run refreshing	15 ms max./ 15 ms max.	NX-OC2633	UC1, N, L, CE, RCM, KC
	2 points	N.O.+N.C.		Free-Run refreshing	15 ms max./ 15 ms max.	NX-OC2733	UC1, N, CE, RCM, KC
	8 points	N.O.	250 VAC/2 A (cosφ=1) 250 VAC/2 A (cosφ=0.4) 24 VDC/2 A 8 A/Unit	Free-Run refreshing	15 ms max./ 15 ms max.	NX-OC4633	UC1, CE, RCM, KC

* To use input refreshing with input changed time, the EtherCAT Coupler Unit with unit version 1.1 or later and the
Sysmac Studio version 1.07 or higher are required.

Product Name	Specification					Model	Standards
Product Name	Number of points	Internal I/O common	Maximum value of load current	I/O refreshing method	ON/OFF response time	Model	Standards
DC Input/ Transistor Output Unit (MIL Connector, 30 mm Width)	Outputs: 16 points Inputs: 16 points	Outputs: NPN Inputs: For both NPN/PNP	Outputs: 12 to 24 VDC Inputs: 24 VDC	Switching Synchronous I/O refreshing and Free-Run refreshing	Outputs: 0.1 ms max./ 0.8 ms max. Inputs: 20 μs max./ 400 μs max.	NX-MD6121-5	UC1, CE, RCM, KC
	Outputs: 16 points Inputs: 16 points	Outputs: PNP Inputs: For both NPN/PNP	Outputs: 24 VDC Inputs: 24 VDC		Outputs: 0.5 ms max./ 1.0 ms max. Inputs: 20 μs max./ 400 μs max.	NX-MD6256-5	UC1, CE, RCM, KC
DC Input/ Transistor Output Unit (Fujitsu Connector, 30 mm Width)	Outputs: 16 points Inputs: 16 points	Outputs: NPN Inputs: For both NPN/PNP	Outputs: 12 to 24 VDC Inputs: 24 VDC	Switching Synchronous I/O refreshing and Free-Run refreshing	Outputs: 0.1 ms max./ 0.8 ms max. Inputs: 20 μs max./ 400 μs max.	NX-MD6121-6	UC1, CE, RCM, KC

Product Name	Specification									Model	Stand- ards
Product Name	Num- ber of points	Input range	Reso- lution	Con- version value, decimal number (0 to 100%)	Over all accuracy (25°C)	Input method	Con- ver- sion time	Input im- ped- ance	I/O re- freshing method	Model	Stand- ards
Voltage Input Unit	2 points	-10 to +10 V	1/8000	-4000 to 4000	±0.2% (full scale)	Single- ended input	250 μs/ point	1 MΩ min.	Free-Run refreshing	NX-AD2603	UC1, N, L, CE, RCM, KC
			1/8000	-4000 to 4000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD2604
			1/30000	-15000 to 15000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD2608
	4 points		1/8000	-4000 to 4000	±0.2% (full scale)	Single- ended input	250 μs/ point		Free-Run refreshing	NX-AD3603
			1/8000	-4000 to 4000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD3604
			1/30000	-15000 to 15000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD3608
	8 points		1/8000	-4000 to 4000	±0.2% (full scale)	Single- ended input	250 μs/ point		Free-Run refreshing	NX-AD4603
			1/8000	-4000 to 4000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD4604
			1/30000	-15000 to 15000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD4608
Current Input Unit	2 points	4 to 20 mA	1/8000	0 to 8000	±0.2% (full scale)	Single- ended input	250 μs/ point	250 Ω	Free-Run refreshing	NX-AD2203
			1/8000	0 to 8000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD2204
			1/30000	0 to 30000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD2208
	4 points		1/8000	0 to 8000	±0.2% (full scale)	Single- ended input	250 μs/ point		Free-Run refreshing	NX-AD3203
			1/8000	0 to 8000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD3204
			1/30000	0 to 30000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD3208
	8 points		1/8000	0 to 8000	±0.2% (full scale)	Single- ended input	250 μs/ point	85 Ω	Free-Run refreshing	NX-AD4203
			1/8000	0 to 8000	±0.2% (full scale)	Differ- ential Input	250 μs/ point		Free-Run refreshing	NX-AD4204
			1/30000	0 to 30000	±0.1% (full scale)	Differ- ential Input	10 μs/ point		Selectable Synchro- nous I/O refreshing or Free- Run re- freshing	NX-AD4208

Product Name	Specification							Model	Stand- ards
Product Name	Number of points	Input range	Reso- lution	Output setting value, decimal number (0 to 100%)	Over all accuracy (25°C)	Con- version time	I/O refreshing method	Model	Stand- ards
Voltage Output Unit	2 points	-10 to +10 V	1/8000	-4000 to 4000	±0.3% (full scale)	250 μs/ point	Free-Run refreshing	NX-DA2603	UC1, N, L, CE, RCM, KC
	2 points		1/30000	-15000 to 15000	±0.1% (full scale)	10 μs/ point	Selectable Synchronous I/O refreshing or Free-Run refreshing	NX-DA2605
	4 points		1/8000	-4000 to 4000	±0.3% (full scale)	250 μs/ point	Free-Run refreshing	NX-DA3603
	4 points		1/30000	-15000 to 15000	±0.1% (full scale)	10 μs/ point	Selectable Synchronous I/O refreshing or Free-Run refreshing	NX-DA3605
Current Output Unit	2 points	4 to 20 mA	1/8000	0 to 8000	±0.3% (full scale)	250 μs/ point	Free-Run refreshing	NX-DA2203
	2 points		1/30000	0 to 30000	±0.1% (full scale)	10 μs/ point	Selectable Synchronous I/O refreshing or Free-Run refreshing	NX-DA2205
	4 points		1/8000	0 to 8000	±0.3% (full scale)	250 μs/ point	Free-Run refreshing	NX-DA3203
	4 points		1/30000	0 to 30000	±0.1% (full scale)	10 μs/ point	Selectable Synchronous I/O refreshing or Free-Run refreshing	NX-DA3205

Product Name	Specification							Model	Standa- rds
Product Name	Number of points	Input type	Re- solution (25°C)	Over all accuracy (25°C)	Con- version time	I/O re- fresh- ing method	Terminals	Model	Standa- rds
Thermo- couple Input type	2 points	Thermo- couple	0.1°C max. *1	Refer to the Reference accuracy and temperature coefficient according to the input type and measurement temperature of NX-series Temperature Input Unit in the Sysmac Integrated Catalog (Cat. No. P072).	250 ms/ Unit	Free- Run re- freshing	16 Terminals	NX-TS2101	UC1, N, L, CE, RCM, KC
	4 points		0.1°C max. *1		250 ms/ Unit		16 Ter- minals x 2	NX-TS3101
	2 points		0.01°C max.		10 ms/ Unit		16 Terminals	NX-TS2102
	4 points		0.01°C max.		10 ms/ Unit		16 Ter- minals x 2	NX-TS3102
	2 points		0.001°C max.		60 ms/ Unit		16 Terminals	NX-TS2104
	4 points		0.001°C max.		60 ms/ Unit		16 Ter- minals x 2	NX-TS3104
Re- sistance Thermo- meter Input type	2 points	Re- sistance Thermo- meter (Pt100/ Pt1000, three- wire) *2	0.1°C max.		250 ms/ Unit		16 Terminals	NX-TS2201
	4 points		0.1°C max.		250 ms/ Unit		16 Ter- minals x 2	NX-TS3201
	2 points		0.01°C max.		10 ms/ Unit		16 Terminals	NX-TS2202
	4 points		0.01°C max.		10 ms/ Unit		16 Ter- minals x 2	NX-TS3202
	2 points		0.001°C max.		60 ms/ Unit		16 Terminals	NX-TS2204
	4 points		0.001°C max.		60 ms/ Unit		16 Ter- minals x 2	NX-TS3204

*1. The resolution is 0.2°C max. when the input type is R, S, or W.
*2. The NX-TS2202 and NX-TS3202 only supports Pt100 three-wire sensor.

Product Name	Specification							Model	Stand- ards
	CT input section		Control output section
	Number of inputs	Maximum heater current	Number of outputs	Internal I/O common	Maximum load current	Rated voltage	I/O refreshing method
Heater Burnout Detection Unit	4	50 AAC	4	NPN	0.1 A/point, 0.4 A/Unit	12 to 24 VDC	Free-Run refreshing	NX-HB3101	UC1, CE, RCM, KC
Heater Burnout Detection Unit	4	50 AAC	4	PNP	0.1 A/point, 0.4 A/Unit	24 VDC	Free-Run refreshing	NX-HB3201	UC1, CE, RCM, KC

Product Name	Specification					Model	Standards
Product Name	Number of Model Standards points	Conversion cycle	I/O refreshing method *	Load cell excitation voltage	Input range	Model	Standards
Load Cell Input Unit	1	125 μs	• Free-Run refreshing • Synchronous I/O refreshing • Task period prioritized refreshing	5 VDC ± 10%	-5.0 to 5.0 mV/V	NX-RS1201	UC1, CE, RCM, KC

* Refer to the NX-series Load Cell Input Unit User’s Manual (W565) for detailed information on I/O refresh cycle.

Product Name	Specification					Model	Standards
Product Name	Number of channels	External inputs	Maximum response frequency	I/O refreshing method	Number of I/O entry mappings	Model	Standards
Incremental Encoder Input Unit	1 (NPN)	3 (NPN)	500 kHz	• Free-Run refreshing • Synchronous I/O refreshing	1/1	NX-EC0112	UC1, CE, RCM, KC
	1 (PNP)	3 (PNP)	500 kHz			NX-EC0122	UC1, N, L, CE, RCM, KC
	1	3 (NPN)	4 MHz			NX-EC0132	UC1, CE, RCM, KC
	1	3 (PNP)	4 MHz			NX-EC0142	UC1, N, L, CE, RCM, KC
	2 (NPN)	None	500 kHz		2/2	NX-EC0212	UC1, CE, RCM, KC
	1 (PNP)	None	500 kHz		2/2	NX-EC0222	UC1, N, L, CE, RCM, KC

Product Name	Specification					Model	Standards
Product Name	Number of channels	Input/ Output form	Maximum data length	Encoder power supply	Type of external connections	Model	Standards
SSI Input Unit	1	EIA standard RS-422-A	32 bits	24 VDC, 0.3 A/CH	Screwless push-in terminal block (12 terminals)	NX-ECS112	UC1, N, L, CE, RCM, KC
SSI Input Unit	2	EIA standard RS-422-A	32 bits	24 VDC, 0.3 A/CH	Screwless push-in terminal block (12 terminals)	NX-ECS212	UC1, N, L, CE, RCM, KC

Product Name	Specification							Model	Stand- ards
Product Name	Number of channels *1	External inputs	External outputs	Max- imum pulse output speed	I/O refreshing method	Number of I/O entry map- pings	Control output inte- face	Model	Stand- ards
Pulse Output Unit	1 (NPN)	2 (NPN)	1 (NPN)	500 kpps	• Synchronous I/O refreshing • Task period prioritized refreshing *2	1/1	Open collector output	NX-PG0112	UC1, N, CE, RCM, KC
	1 (PNP)	2 (PNP)	1 (PNP)	500 kpps		1/1	Open collector output	NX-PG0122	UC1, N, L, CE, RCM, KC
	2	5 inputs/ CH (NPN)	3 outputs/ CH (NPN)	4 Mpps		2/2	Line driver output	NX-PG0232-5	UC1, CE, RCM, KC
	2	5 inputs/ CH (PNP)	3 outputs/ CH (PNP)			2/2		NX-PG0242-5
	4	5 inputs/ CH (NPN)	3 outputs/ CH (NPN)			4/4		NX-PG0332-5
	4	5 inputs/ CH (PNP)	3 outputs/ CH (PNP)			4/4		NX-PG0342-5

*1. This is the number of pulse output channels.
*2. Unit version 1.2 or later and an NX-ECC203 EtherCAT Coupler Unit are required.

Product Name	Serial interface	External connection terminals	Number of serial ports	Communications protocol	Model	Standards
Communications Interface Unit	RS-232C	Screwless Clamping Terminal Block	1 port	• No-protocol • Signal lines	NX-CIF101	UL, CE, RCM, KC
	RS-422A/485	Screwless Clamping Terminal Block	1 port		NX-CIF105
	RS-232C	D-Sub connector	2 ports		NX-CIF210

Product Name	Specification			Model	Standards
Product Name	Number of IO-Link ports	I/O refreshing method	I/O connection terminals	Model	Standards
IO-Link Master Unit	4	Free-Run refreshing	Screwless clamping terminal block	NX-ILM400	UC1, CE, RCM, KC

Product Name	Specification	Model	Standards
Additional NX Unit Power Supply Unit	Power supply voltage: 24 VDC (20.4 to 28.8 VDC) NX Bus power supply capacity: 10 W max.	NX-PD1000	UC1, N, L, CE, RCM, KC
Additional I/O Power Supply Unit	Power supply voltage: 5 to 24 VDC (4.5 to 28.8 VDC) I/O power feed maximum current: 4 A	NX-PF0630	UC1, N, L, CE, RCM, KC
Additional I/O Power Supply Unit	Power supply voltage: 5 to 24 VDC (4.5 to 28.8 VDC) I/O power feed maximum current: 10 A *	NX-PF0730	UC1, N, L, CE, RCM, KC
I/O Power Supply Connection Unit	Number of I/O power terminals: IOG: 16 terminals Current capacity of I/O power terminal: 4 A/terminal max.	NX-PC0010	UC1, N, L, CE, RCM, KC
	Number of I/O power terminals: IOV: 16 terminals Current capacity of I/O power terminal: 4 A/terminal max.	NX-PC0020	UC1, N, L, CE, RCM, KC
	Number of I/O power terminals: IOV: 8 terminals, IOG: 8 terminals Current capacity of I/O power terminal: 4 A/terminal max	NX-PC0030	UC1, N, L, CE, RCM, KC
Shield Connection Unit	Number of shield terminals: 14 terminals (The following two terminals are functional ground terminals.)	NX-TBX01	UC1, N, L, CE, RCM, KC

* Use the NX-PF0730 at 4 A or less on the CPU Rack where the NX1P2 CPU Unit is mounted.

NX-series Units on previous pages and NX-series Safety Units can be used by connecting to the EtherCAT Coupler Unit that is connected to the built-in EtherCAT port on the NX1P2 CPU Unit.

Product Name	Communications cycle in DC Mode	Current consumption	Maximum I/O power supply current	Model	Standards
EtherCAT Coupler Unit *1	250 to 4000 μs *2	1.45 W max.	4 A	NX-ECC201	UC1, N, L, CE, KC
	250 to 4000 μs *2	1.45 W max.	10 A	NX-ECC202	UC1, N, L, CE, KC
	125 to 10000 μs *2	1.25 W max.	10 A	NX-ECC203	UC1, CE, KC

*1. One End Cover NX-END01 is provided with the EtherCAT Coupler Unit.
*2. This depends on the specifications of the EtherCAT master. For example, the values are as follows when the
      EtherCAT Coupler Unit is connected to the built-in EtherCAT port on an NJ5-series CPU Unit: 500 μs, 1,000 μs,
      2,000 μs, and 4,000 μs. Refer to the NJ/NX-series CPU Unit Built-in EtherCAT Port User' Manual (Cat. No. W505)
      for the specifications of the built-in EtherCAT ports on NJ/NX-series CPU Units. This also depends on the unit
      configuration.

Appearance	Specification					Model	Standards
Appearance	Maximum number of safety I/O points	Program capacity	Number of safety master connections	I/O refreshing method	Unit version	Model	Standards
	256 points	512 KB	32	Free-Run refreshing	Ver.1.1	NX-SL3300	Refer to the NX-series Safety Control Units in the Sysmac Integrated Catalog (Cat. No. P072).
	1024 points	2048 KB	128	Free-Run refreshing	Ver.1.1	NX-SL3500

Note: Connect the Safety CPU Unit to the NX1P2 CPU Unit via the EtherCAT Coupler Unit.

Appear- ance	Specification								Model	Standards
Appear- ance	Number of safety input points	Number of test output points	Inter- nal I/O com- mon	Rated input volt- age	OMRON special safety input devices	Number of safety slave con- nec- tions	I/O re- freshing method	Unit ver- sion	Model	Standards
	4 points	2 points	Sinking inputs (PNP)	24 VDC	Can be con- nected.	1	Free-Run refreshing	Ver.1.1	NX-SIH400	Refer to the NX-series Safety Control Units in the Sysmac Integrated Catalog (Cat. No. P072).
	8 points	2 points	Sinking inputs (PNP)	24 VDC	Cannot be con- nected.	1	Free-Run refreshing	Ver.1.0	NX-SID800

Note: Connect the Safety Input Unit to the NX1P2 CPU Unit via the EtherCAT Coupler Unit.

Appear- ance	Specification							Model	Standards
Appear- ance	Number of Model safety output points	Internal I/O common	Maximum load current	Rated volt- age	Number of safety slave connec- tions	I/O re- freshing method	Unit ver- sion	Model	Standards
	2 points	Sourcing outputs (PNP)	2.0 A/point, 4.0 A/Unit at 40°C, and 2.5A/Unit at 55°C The maximum load current depends on the installation orientation and ambient temperature.	24 VDC	1	Free-Run refreshing	Ver.1.0	NX-SOH200	Refer to the NX-series Safety Control Units in the Sysmac Integrated Catalog (Cat. No. P072).
	4 points	Sourcing outputs (PNP)	0.5 A/point and 2.0 A/Unit	24 VDC	1	Free-Run refreshing	Ver.1.0	NX-SOD400

Note: Connect the Safety Output Unit to the NX1P2 CPU Unit via the EtherCAT Coupler Unit.

Please purchase a DVD and required number of licenses the first time you purchase the Sysmac Studio. DVDs and licenses are available individually.
Each model of licenses does not include any DVD.

Product Name	Specification			Model	Stand- ards
Product Name		Number of licenses	Media	Model	Stand- ards
Sysmac Studio Standard Edition Ver.1.[][]	The Sysmac Studio is the software that provides an integrated environment for setting, programming, debugging and maintenance of machine automation controllers including the NJ/NX-series CPU Units, NY-series Industrial PC, EtherCAT Slave, and the HMI. Sysmac Studio runs on the following OS. Windows 7 (32-bit/64-bit version)/Windows 8 (32- bit/64-bit version)/Windows 8.1 (32-bit/64-bit version)/Windows 10 (32-bit/64-bit version) The Sysmac Studio Standard Edition DVD includes Support Software to set up EtherNet/IP Units, DeviceNet slaves, Serial Communications Units, and Support Software for creating screens on HMIs (CXDesigner). For details, refer to the Sysmac Integrated Catalog (Cat. No. P072).	--- (Media only)	DVD	SYSMAC-SE200D	---
Sysmac Studio Standard Edition Ver.1.[][]		1 license *	---	SYSMAC-SE201L	---

* Multi licenses are available for the Sysmac Studio (3, 10, 30, or 50 licenses).

Use Straight STP (shielded twisted-pair) cable of category 5 or higher with double shielding (braiding and aluminum foil tape) for EtherCAT.
For EtherNet/IP, required specification for the communications cables varies depending on the baud rate.
For 100BASE-TX/10BASE-T, use an STP (shielded twisted-pair) cable of Ethernet category 5 or higher.
In the table, materials indicated available for EtherNet/IP 100BASE-TX are available for both of 100BASE-TX and 10BASE-T.

Item	Recommended manufacturer	Cable length (m)	Model
Cable with Connectors on Both Ends (RJ45/ RJ45) Standard RJ45 plugs type 1 Wire Gauge and Number of Pairs: AWG26, 4- pair Cable Cable Sheath material: LSZH 2 Cable color: Yellow *3	OMRON	0.3	XS6W-6LSZH8SS30CM-Y
		0.5	XS6W-6LSZH8SS50CM-Y
		1	XS6W-6LSZH8SS100CM-Y
		2	XS6W-6LSZH8SS200CM-Y
		3	XS6W-6LSZH8SS300CM-Y
		5	XS6W-6LSZH8SS500CM-Y
Cable with Connectors on Both Ends (RJ45/ RJ45) Rugged RJ45 plugs type *1 Wire Gauge and Number of Pairs: AWG22, 2- pair Cable Cable color: Light blue	OMRON	0.3	XS5W-T421-AMD-K
		0.5	XS5W-T421-BMD-K
		1	XS5W-T421-CMD-K
		2	XS5W-T421-DMD-K
		5	XS5W-T421-GMD-K
		10	XS5W-T421-JMD-K
Cable with Connectors on Both Ends (M12 Straight/M12 Straight) Shield Strengthening Connector cable *4 M12/Smartclick Connectors Wire Gauge and Number of Pairs: AWG22, 2- pair Cable Cable color: Black	OMRON	0.5	XS5W-T421-BM2-SS
		1	XS5W-T421-CM2-SS
		2	XS5W-T421-DM2-SS
		3	XS5W-T421-EM2-SS
		5	XS5W-T421-GM2-SS
		10	XS5W-T421-JM2-SS
Cable with Connectors on Both Ends (M12 Straight/RJ45) Shield Strengthening Connector cable *4 M12/Smartclick Connectors Rugged RJ45 plugs type Wire Gauge and Number of Pairs: AWG22, 2- pair Cable Cable color: Black	OMRON	0.5	XS5W-T421-BMC-SS
		1	XS5W-T421-CMC-SS
		2	XS5W-T421-DMC-SS
		3	XS5W-T421-EMC-SS
		5	XS5W-T421-GMC-SS
		10	XS5W-T421-JMC-SS

*1. Standard type cables length 0.2, 0.3, 0.5, 1, 1.5, 2, 3, 5, 7.5, 10, 15 and 20 m are available.
      Rugged type cables length 0.3, 0.5, 1, 2, 3, 5, 10 and 15 m are available.
      For details, refer to the XS5/XS6 Industrial Ethernet Connectors Datasheet (Cat. No. G019).
*2. The lineup features Low Smoke Zero Halogen cables for in-cabinet use and PUR cables for out-of-cabinet use.
      Although the LSZH cable is single shielded, its communications and noise characteristics meet the standards.
*3. Cables colors are available in blue, yellow, or Green.
*4. For details, contact your OMRON representative.

Item	Appearance	Recommended manufacturer	Model
Cables	---	Hitachi Metals, Ltd.	NETSTAR-C5E SAB 0.5×4P *
	---	Kuramo Electric Co.	KETH-SB *
	---	SWCC Showa Cable Systems Co.	FAE-5004 *
RJ45 Connectors	---	Panduit Corporation	MPS588-C *

* We recommend you to use above cable and connector together.

Item	Appearance	Recommended manufacturer	Model
Cables	---	Kuramo Electric Co.	KETH-PSB-OMR *
Cables	---	JMACS Japan Co., Ltd.	PNET/B *
RJ45 Assembly Connector		OMRON	XS6G-T421-1 *

Note: Connect both ends of cable shielded wires to the connector hoods.
* We recommend you to use above cable and connector together.

Product Name	Specification		Model	Stand- ards
EtherCAT junction slaves *1	3 ports. Power supply voltage: 20.4 to 28.8 VDC (24 VDC -15 to +20%). Current consumption (A): 0.08		GX-JC03	CE, UC1
EtherCAT junction slaves *1	6 ports. Power supply voltage: 20.4 to 28.8 VDC (24 VDC -15 to +20%). Current consumption (A): 0.17		GX-JC06	CE, UC1
Industrial Switching Hubs for EtherNet/IP and Ethernet *2	Quality of Service (QoS): EtherNet/IP control data priority Failure detection: Broadcast storm and LSI error detection 10/100BASE-TX, Auto-Negotiation	3 ports. Current consumption (A): 0.22 Power supply connector included.	W4S1-03B	UC, CE
		5 ports. Current consumption (A): 0.22 Power supply connector included.	W4S1-05B	UC, CE
		5 ports. Current consumption (A): 0.22 Failure detection Power supply connector and Connector for informing error included.	W4S1-05C	CE
Memory Cards	SD memory card, 2 GB		HMC-SD291	N, L, CE
Memory Cards	SD memory card, 4 GB		HMC-SD491	CE
Battery	The battery is not mounted when the product is shipped. To turn OFF the power supply to the equipment for a certain period of time by using the clock data for programming, event logs, etc., you need a separately-sold battery to retain the clock data. Refer to the Battery page for details.		CJ1W-BAT01	---
End Cover (For NX1P2 CPU Unit) *3	Must be connected to the right end of the CPU Rack. One End Cover is provided with the CPU Unit.		NX-END02	---
End Cover (For EtherCAT Coupler Unit) *3	One End Cover is provided with the EtherCAT Coupler Unit.		NX-END01	---
DIN Tracks	Length: 0.5 m; Height: 7.3 mm		PFP-50N	---
DIN Tracks	Length: 1 m; Height: 7.3 mm		PFP-100N	---
End Plate	There are 2 stoppers provided with CPU Units and I/O Interface Units as standard accessories to secure the Units on the DIN Track.		PFP-M	---
Unit/Terminal Block Coding Pins	For 10 Units (Terminal Block: 30 pins, Unit: 30 pins)		NX-AUX02	---
DIN Track Insulation Spacers	A Spacer to insulate the control panel from the DIN Track. To insulate the EtherCAT Slave Terminal from the control panel, use Din Track Insulation Spacers.		NX-AUX01	--

Product Name	Specification				Model	Standards
Product Name	No. of terminals	Terminal number indications	Ground terminal mark	Terminal current capacity	Model	Standards
Terminal Blocks	8	A/B	None	10 A	NX-TBA082	---
	12	A/B			NX-TBA122
	16	A/B			NX-TBA162
	12	C/D			NX-TBB122
	16	C/D			NX-TBB162
	8	A/B	Provided		NX-TBC082
	16	A/B	Provided		NX-TBC162

*1. EtherCAT junction slaves cannot be used for EtherNet/IP and Ethernet.
*2. Industrial switching hubs cannot be used for EtherCAT.
*3. Use the NX-END02 End Cover only for the CPU Unit and the NX-END01 End Cover only for the EtherCAT Coupler Unit.

NX1P2

Up to eight axes of control via EtherCAT

International Standards

NX-series NX1P2 CPU Units

Option Boards (For CPU Units)

NX Units

Digital Input Units

Digital output Units

Digital Mixed I/O Units

Analog Input Units

Analog Output Units

Temperature Input Units

Heater Burnout Detection Units

Load Cell Input Unit

Position interface: Incremental Encoder Input Units

Position interface: SSI Input Units

Position interface: Pulse Output Units

Communications Interface Units

IO-Link Master Unit

System Units

EtherCAT Coupler Units

Safety CPU Units

Safety Input Units

Safety Output Units

Automation Software Sysmac Studio

Recommended EtherCAT and EtherNet/IP Communications Cables

Cable with Connectors (For EtherCAT only)

Cables / Connectors (For EtherCAT or EtherNet/IP (100BASE-TX))

Wire Gauge and Number of Pairs: AWG24, 4-pair Cable

Wire Gauge and Number of Pairs: AWG22, 2-pair Cable

Optional Products/Maintenance Products/DIN Track Accessories

Product Category